only one name means protektion? www.protekdevices.com 05064.r6 2/11 page 1 05064 587B062LPE - 587b302lpe l ow pr ofi le 240v ac p ow er l in e su r g e su ppre sso r d e sc r i p tion the 587b low profle (lpe) series is designed for european applicatons where no line to ground or neutral to ground suppression is allowed. these modules employ a three stage technology proven to be the most cost efectve and reli - able method in protectng sensitve electronic equipment from over voltage transients. this series is designed to protect ac powered equipment from the 6,000 volt peak open circuit voltage and 3,000 amp short circuit current as defned in ansi/ieee c62.41, category ci. the 587bxxxlpe series ofers a high degree of protecton against 240 vac emi line noise. it is ideal for protectng 800 volt components because the solid state tvs technology assures that the line-to-neutral voltage will not exceed 800 volts. while the modules are designed for transient voltage protecton, the advanced circuitry will also atenuate the amplitude and slow the rate of rise of high frequency noise actng as an emi flter. the 587bxxxlpe series includes common mode protecton, which are efectve in reducing interference from line to equipment and are efectve in reducing equipment generated noise to meet fcc, vde and csa interference requirements. fe atu re s ? compatble with iec 61000-4-5 (surge): 1ka, 8/20s, level 4 (line- gnd) & 333a, level 4 (line-line) ? meets ansi/ieee c62.41 outdoor requirements ? listed to csa, file lr65240 (except 587b302lpe) ? diferental mode protecton ? low clamping voltage ? nanosecond response time ? long life and maintenance free ? finger safe connectons m e chanica l cha r act er istics ? low profle plastc package ? approximate weight: 360 grams ? flammability ratng ul 94v-0 a ppl ications ? hard wired equipment ac power protecton ? load side distributon systems ? secondary protecton for light industrail ac power l ow pr ofi le figu re 1 t r ansi e nt vo l tag e th re at con d ition 0 10 20 30 40 50 60 t - time - s 4 6 kilovolts 2 0 figu re 2 ty p ica l c l a mp ing action of a 15a m o d u le 0 10 20 30 40 50 60 t - time - s 4 6 kilovolts 2 0 8 figures 1 and 2 are photographs of digitzed waveforms showing the typical clamping acton of a 15a module. a 12 ohm resistor is used to repre - sent a 10a equipment load. the load is then subjected to the ansi/ieee c62.41 catagory ci test conditons (6000v/3000a). these photographes contrast the efect on equipment with and without the protector.
only one name means protektion? www.protekdevices.com 05064.r6 2/11 page 2 05064 587B062LPE - 587b302lpe ty p ica l de vic e cha r act er istics m a x i m u m r atings @ 25c unless o therwise specifed p a r a me t er sy mb o l va l u e units operatng line voltage: +10% v o 240 volts ac line current: 587B062LPE/587b102lpe/587b162lpe/587b302lpe - 6/10/16/30 amps peak transient voltage - 6000 volts peak transient current - 3000 amps current leakage @ 2400 volts ac: line-to-neutral - 1 ma operatng temperature - note 1 t a -40 to 85 c storage temperature - note 1 t stg -40 to 85 c n ot e s 1. measured at the center of the mountng surface. ele ct r ica l cha r act er istics @ 25c unless o therwise specifed p r ot e ction m o de (n ote 1) m a x i m u m c l a mp ing vo l tag e (n ote 2) vo l ts o pe n ci r cuit vo l tag e (n ote 2) @1.2/50 s vo l ts sho r t ci r cuit cu rre nt (n ote 2) @ 8/20 s a mp s line to neutral 800 6000 3000 n ot e s 1. diferental mode protecton: line to neutral. 2. test conditon responses to transient voltages. a rre sto r de finitions clamping voltage: the clamping voltage of an arrester is the voltage that appears across its terminals during conducton of a transient current. standard wave form: the waveform of a surge current or voltage is designated by a combinaton of two numbers. the frst number is for the tme of the wave front expressed in microseconds from zero to the peak of the wave. the second number is for the tme of the wavetail also expressed in microseconds from zero to the instant that the wavetail reaches one half of the crest or peak value, i.e., 8/20 s waveform. transient current: the transient current of an arrestor is the peak surge current which fows through the arrester when voltage clamping occurs. o per ation for maximum efectveness, the protector should be installed directly afer the ac line on/of switch and fuse. this will protect the electronics from the ac line switch arcing and the severe transients caused by a fuse clearing. some heat is produced when operatng at full current load, and heat sinking may be required to maintain case temperature below 85c. the case temperature is measured at the center of the mountng surface. the unit should not be mounted to a low combustng temperature material such as wood. high energy transients will cause a large circulatng current in the ac input line (2,500a is possible). to prevent electromagnetc coupling, the ac line on the input side of the protector must be dressed away from other wiring, magnetc shielding may be required. in additon, the electrical service must be connected to a low imped - ance earth ground.
only one name means protektion? www.protekdevices.com 05064.r6 2/11 page 3 05064 587B062LPE - 587b302lpe p ac k ag e info rm ation out l in e d i me nsions d i m m i ll i me t er s inch e s m in m a x m in m a x a 96.8 3.81 b 88.9 3.50 c 110.92 111.68 4.37 4.40 d 14.43 0.586 e 43.89 44.39 1.62 1.72 f 27.9 1.10 g 58.04 58.80 2.29 2.32 o rder ing info rm ation b as e p a r t nu mber (xx = v oltage) m a rk ing 587bxxxlpe part number, date code, voltage, logo, current ratng, csa logo a b c d e f g device marking line in dia. 0.181 neutral in ground in line 1 out line 2 out neutral 1 out neutral 2 out ground out
only one name means protektion? www.protekdevices.com 05064.r6 2/11 page 4 05064 587B062LPE - 587b302lpe co mp any info rm ation co mp any pr ofile protek devices, based in tempe, arizona usa, is a manufacturer of transient voltage suppression (tvs) products designed specifcally for the protecton of electronic systems from the efects of lightning, electrostatc discharge (esd), nuclear electromagnetc pulse (nemp), in - ductve switching and emi/rfi. with over 25 years of engineering and manufacturing experience, protek designs tvs devices that provide applicaton specifc protecton solutons for all electronic equipment/systems. protek devices analog products division, also manufactures analog interface, control, rf and power management products. copyright ? protek devices 1998 - this literature is subject to all applicable copyright laws and is not for resale in any manner. specifications: protek reserves the right to change the electrical and or mechanical characteristcs described herein without notce. design changes: protek reserves the right to discontnue product lines without notce and that the fnal judgement concerning selecton and specifcatons is the buyers and that in furnishing engineering and technical assistance. protek assumes no responsibility with respect to the selecton or specifcatons of such products. protek makes no warranty, representaton or guarantee regarding the suitability of its products for any partcular purpose, nor does protek assume any liability arising out of the applicaton or use of any product or circuit and specifcally disclaims any and all liability without limitaton special, consequental or incidental damages. life support policy: protek devices products are not authorized for use in life support systems without writen consent from the factory. patent information: this device is patented under u.s. patent no. 4,563,720 contact us c orporate h eadquarters 2929 south fair lane tempe, arizona 85282 usa by t elephone general: 602-431-8101 sales: 602-414-5109 customer service: 602-414-5114 by f ax general: 602-431-2288 by e-mail: sales: sales@protekdevices.com customer service: service@protekdevices.com technical support: support@protekdevices.com w eb www.protekdevices.com www.protekanalog.com
|
